# MakerGear M2: specs, SimplyPrint compatibility and setup

> **Compatible** (We're sure). It's known to work with SimplyPrint, from documentation, the protocol or owners' prints.

- By MakerGear, USA
- Canonical page: https://staging.simplyprint.io/compatibility/makergear-m2

## MakerGear M2 at a glance

The MakerGear M2 is a 3D printer by MakerGear with a 200 x 250 x 200 mm build volume.

- Build volume: 200 x 250 x 200 mm
- Prints well: PLA, PETG, TPU & flexibles

## Connect the MakerGear M2 to SimplyPrint

| Way of connecting | Status | What you need | Notes |
| :--- | :--- | :--- | :--- |
| SimplyPrint | Compatible |  | Through Klipper (Moonraker) or OctoPrint |
| Klipper (Moonraker) | Compatible | Nothing extra: the printer runs Klipper as it ships |  |
| OctoPrint (Directly, over USB) | Compatible | A Raspberry Pi running OctoPrint, plugged into the printer with a USB cable |  |

- [How to set up SimplyPrint on MakerGear M2](https://staging.simplyprint.io/setup-guide/makergear/m2.md)
- [How to set up Mainsail on MakerGear M2](https://docs.mainsail.xyz/setup)
- [How to set up Fluidd on MakerGear M2](https://docs.fluidd.xyz/installation)
- [How to set up OctoPrint on MakerGear M2](https://staging.simplyprint.io/compatibility/makergear-m2/octoprint-setup)

### What works with SimplyPrint

Connected through Klipper (Moonraker), SimplyPrint supports most of what it offers on the MakerGear M2: the camera and AI failure detection, remote printing, skipping objects, temperature and movement control and AutoPrint. Not yet in SimplyPrint through Klipper (Moonraker): download the file before the print starts. Not available through Klipper (Moonraker): print binary G-code (.bgcode).

## What slicer to use for the MakerGear M2

Use Cura or Kiri:Moto: each has a ready-made profile for the MakerGear M2.

- [Cura](https://staging.simplyprint.io/features/slicer/cura): Ready-made profile for the MakerGear M2 · Runs in the SimplyPrint cloud
- [Kiri:Moto](https://staging.simplyprint.io/features/slicer/kirimoto): Ready-made profile for the MakerGear M2 · Runs in the SimplyPrint cloud
- [PrusaSlicer](https://staging.simplyprint.io/features/slicer/prusaslicer): No profile for the MakerGear M2 · Runs in the SimplyPrint cloud
- [OrcaSlicer](https://staging.simplyprint.io/features/slicer/orcaslicer): No profile for the MakerGear M2 · Runs in the SimplyPrint cloud
- [BambuStudio](https://staging.simplyprint.io/features/slicer/bambustudio): No profile for the MakerGear M2 · Runs in the SimplyPrint cloud
- [ElegooSlicer](https://staging.simplyprint.io/features/slicer/elegooslicer): No profile for the MakerGear M2 · Runs in the SimplyPrint cloud
- [CrealityPrint](https://staging.simplyprint.io/features/slicer/crealityprint): No profile for the MakerGear M2 · Runs in the SimplyPrint cloud

We only list slicers you can use in the SimplyPrint cloud, so there may be others for the MakerGear M2.

## The app for the MakerGear M2

SimplyPrint works as the MakerGear M2's app: on your phone and in any browser, with a slicer in the cloud.

- An app for iPhone and Android, the same in any browser, and a slicer in the cloud.
- More than monitoring: a print queue, AI failure detection, AutoPrint and accounts for a team.
- Printers from many brands in one place, side by side.
- Hosted in Frankfurt, Germany, under the GDPR.

[Connect the MakerGear M2 to SimplyPrint, free](https://staging.simplyprint.io/setup-guide/makergear/m2) · [App Store](https://apps.apple.com/app/simplyprint-3d/id1519749400) · [Google Play](https://play.google.com/store/apps/details?id=com.simplyprint.appdev)

## Automate the MakerGear M2

### Ways to automate it

- [Your own ejection G-code](https://staging.simplyprint.io/features/autoprint/custom): Write the routine that clears your plate, and AutoPrint runs it after every print.
- [A robot arm, or anything with an API](https://staging.simplyprint.io/features/autoprint/api): Tell SimplyPrint the plate is clear through the API or a webhook, from a robot arm or your own system.
- [Clear it by hand, keep the queue](https://staging.simplyprint.io/features/autoprint/manual-mode): AutoPrint waits for you to mark the plate clear, then starts the next job.

[How AutoPrint works](https://staging.simplyprint.io/features/autoprint). AutoPrint comes with the Pro plan and up.

## MakerGear M2 specifications: bed size, print height and more

### Size

- Build volume: 200 x 250 x 200 mm
- Bed type: Rectangle
- Bed size: 200 x 250 mm
- Max print height: 200 mm

### Printing

- Max extruder temperature: 300 °C
- Has heated bed: Yes
- Max bed temperature: 110 °C
- Number of nozzles: 1
- Direct drive: Yes
- Probing tool / Auto Bed Leveling: No
- Filament width: 1.75 mm

### Connecting

- Supports serial printing: Yes
- Shipped firmware: Marlin

### Files and slicing

- Supported file formats: G-code (.gcode, .gco, .g)

### The printer

- Printer manufacturer / brand: MakerGear
- Printer model name: M2
- Made by a company from: USA

## What filament can the MakerGear M2 print?

Filament compatibility for the MakerGear M2: the materials it can handle, judged from its hotend, bed, chamber and enclosure.

| Filament | Suitability | Notes |
| :--- | :--- | :--- |
| PLA | Great | The easiest filament to print. Works on almost any printer; a heated bed helps adhesion but is not required. |
| PETG | Great | Comfortably in range (PETG likes a ~230-250C hotend and a ~70-85C bed). |
| TPU & flexibles | Great | The direct-drive extruder feeds flexible filament well. Print slowly for clean results. |
| ABS & ASA | With care | The bed is hot enough, but ABS and ASA warp without an enclosure, which is strongly recommended for clean prints. |
| Nylon (PA) | With care | Possible with care - an enclosure and very dry filament are essential. |
| Polycarbonate (PC) | With care | On the edge - PC really wants an enclosed, hot chamber to avoid warping. |
| Carbon-fiber & glass-filled | With care | Possible if you fit a hardened or wear-resistant nozzle - the abrasive fibers quickly wear a stock brass nozzle. |

### Best filament for the MakerGear M2

Filaments the MakerGear M2 prints well, MakerGear's own first, then the best known.

- [Bambu Lab PLA Basic](https://staging.simplyprint.io/filaments/bambu-lab/pla-basic): PLA, 190-240 °C
- [Bambu Lab PLA Matte](https://staging.simplyprint.io/filaments/bambu-lab/pla-matte): PLA, 190-230 °C
- [SUNLU PLA](https://staging.simplyprint.io/filaments/sunlu/pla): PLA, 190-230 °C
- [Anycubic PETG](https://staging.simplyprint.io/filaments/anycubic/petg): PETG, 190-270 °C
- [Anycubic PLA Basic](https://staging.simplyprint.io/filaments/anycubic/pla-basic): PLA, 190-230 °C
- [Bambu Lab PETG Basic](https://staging.simplyprint.io/filaments/bambu-lab/petg-basic): PETG, 230-270 °C
- [Bambu Lab PETG HF](https://staging.simplyprint.io/filaments/bambu-lab/petg-hf): PETG, 230-270 °C
- [Bambu Lab PETG Translucent](https://staging.simplyprint.io/filaments/bambu-lab/petg-translucent): PETG, 220-250 °C

## Compare the MakerGear M2 with similar printers

- [MakerGear M3 Dual](https://staging.simplyprint.io/compatibility/makergear-m3-dual): Compatible, 203 x 232 x 203 mm, Also by MakerGear · Similar build volume
- [MakerGear M3-SE](https://staging.simplyprint.io/compatibility/makergear-m3-se): Compatible, 203 x 232 x 203 mm, Also by MakerGear · Similar build volume
- [Creality Ender-3](https://staging.simplyprint.io/compatibility/creality-ender-3): Compatible, 220 x 220 x 250 mm, Similar build volume
- [Creality Ender-3 v2](https://staging.simplyprint.io/compatibility/creality-ender-3-v2): Compatible, 220 x 220 x 250 mm, Similar build volume
- [Compare the MakerGear M2 with other printers](https://staging.simplyprint.io/compatibility/compare?compare=makergear-m2#choose)

Affiliate disclosure: Some links on this page are affiliate links. We may earn a commission if you make a purchase, at no extra cost to you. As an Amazon Associate, we earn from qualifying purchases.

## Frequently asked questions

### Is the MakerGear M2 compatible with SimplyPrint?

Yes. You can connect the MakerGear M2 to SimplyPrint via Klipper (Moonraker) or OctoPrint, then slice, queue, start and monitor prints from your browser or the mobile app.

### How do I connect the MakerGear M2 to SimplyPrint?

Follow our step-by-step setup guide for the MakerGear M2. It shows how to connect it via Klipper (Moonraker) or OctoPrint, what you need for each, and which to pick.

### What slicer should I use for the MakerGear M2?

We recommend Cura for the MakerGear M2. You can run it, and 6 other slicers, directly in SimplyPrint's online slicer - no install, on any device, with profiles for the MakerGear M2 kept up to date automatically.

### Can I use OrcaSlicer with the MakerGear M2?

Yes, but OrcaSlicer has no built-in profile for the MakerGear M2 that we know of: start from a similar printer's profile and set the bed size, height and nozzle to match.

### What filament can the MakerGear M2 print?

Based on its specs (hotend up to 300C, heated bed up to 110C), the MakerGear M2 handles PLA, PETG, or TPU & flexibles well. See the full filament guide above for ABS, nylon, PC and composites.

### Does the MakerGear M2 work with OctoPrint or Klipper?

The MakerGear M2 works with OctoPrint or Klipper (Mainsail and Fluidd), and SimplyPrint connects to it through them - so you get cloud access, a queue and camera monitoring on top.

### What is the MakerGear M2's bed size and build volume?

The MakerGear M2 has a 200 x 250 mm print bed and prints up to 200 mm tall, a build volume of about 200 x 250 x 200 mm. See the full specifications table above for bed type, temperatures and more.

### Can the MakerGear M2 eject prints automatically?

There's no kit for it that we support yet, but SimplyPrint's AutoPrint can run your own ejection G-code, work with a robot arm through the API, or wait for you to clear the plate, and then start the next job from your queue.

---

© 2026 SimplyPrint. All rights reserved. This page and the compatibility, specification and review data on it are compiled by SimplyPrint and may not be copied, scraped, reproduced or republished, in whole or in part, without prior written permission. Printer images are the property of their respective manufacturers and are shown for identification purposes only; SimplyPrint claims no ownership of them. Quoted reviews belong to their authors.