Skip to main content

AnkerMake M5C: specs, SimplyPrint compatibility and setup

By AnkerMake, China

AnkerMake M5C image

Does it work with SimplyPrint?

Not compatible We're sure

To our knowledge it can't connect to SimplyPrint, not even through OctoPrint or Klipper.

See printers that work

AnkerMake M5C at a glance

The AnkerMake M5C is a 3D printer by AnkerMake with a 220 x 220 x 250 mm build volume.

Build volume
220 x 220 x 250 mm
Prints well
PLA, PETG, TPU & flexibles
All specifications

Connect the AnkerMake M5C to SimplyPrint

Does the AnkerMake M5C 3D printer work with SimplyPrint, OctoPrint, Mainsail and Fluidd? Each way of connecting it, what it needs, and how to set it up.

Disclaimer: Does not support OctoPrint, Mainsail or Fluidd, according to those who have tried to get it to work. Some discussion on the topic can be found here; https://www.reddit.com/r/AnkerMake/comments/10jz4cs/comment/j5shn1y/?utm_source=share&utm_medium=web3x&utm_name=web3xcss&utm_term=1&utm_content=share_button
  • SimplyPrint

    SimplyPrint

    Not compatible

  • Mainsail Fluidd

    Klipper (Moonraker)

    Not compatible

  • OctoPrint

    OctoPrint

    Directly, over USB

    Not compatible

No known way to connect it to SimplyPrint

Unfortunately, the AnkerMake M5C is currently not, to our knowledge, compatible with OctoPrint, Mainsail, Fluidd, or SimplyPrint. For the best 3D printing experience, consider other 3D printers that are compatible with these softwares.

How we determine compatibility

We consider a printer compatible if it works with one or more of the following:

  • SimplyPrint custom integration for this specific model
  • OctoPrint support (requires the printer to support serial printing)
  • Klipper support (printer can run Klipper, either by flashing compatible firmware or using an external controller/pad)

OctoPrint compatibility is primarily based on whether the printer supports serial communication. If serial printing is not supported, we mark OctoPrint as not compatible.

Note: Some printers have third-party OctoPrint plugins that enable unofficial/custom connections. We don’t maintain a list of these plugins, so they are not reflected in our compatibility data.

See printers that work View Compatible Printers

What slicer to use for the AnkerMake M5C

Use PrusaSlicer, OrcaSlicer, BambuStudio, ElegooSlicer, CrealityPrint, or Cura: each has a ready-made profile for the AnkerMake M5C.

Ready-made profile for the AnkerMake M5C

No profile for the AnkerMake M5C

We only list slicers you can use in the SimplyPrint cloud, so there may be others for the AnkerMake M5C.

Cloud-Based Slicer for AnkerMake M5C: Use PrusaSlicer Online

Use PrusaSlicer and other slicers - directly in your browser with SimplyPrint's online cloud slicer. No installation required. Slice your AnkerMake M5C models from any device, anywhere in the world!

Try Online Slicer Now
Profiles and other slicers

Automatic Profile Updates: Profiles are automatically checked and fetched from the slicer GitHub repositories every day, as well as from our own open-source community-driven slicer profile database. This ensures you always have access to the latest profiles.

Note: Other slicers, such as Simplify3D, ideaMaker, SuperSlicer and KISSlicer, aren't in our cloud, so we don't track their profiles. They may still work well with your AnkerMake M5C: check the slicer's own documentation or forums for a profile. You can also contribute profiles to our open-source slicer profile database on GitHub.

AnkerMake M5C specifications: bed size, print height and more

Its size, temperatures, multi-material and how it connects, from the maker and our own research.

Size

Build volume 220 x 220 x 250 mm
Bed type Square
Bed size 220 x 220 mm
Max print height 250 mm

Printing

Max extruder temperature 300 °C
Has heated bed Yes
Max bed temperature 100 °C
Number of nozzles 1
Direct drive Yes
Probing tool / Auto Bed Leveling Yes
Filament width 1.75 mm

Connecting

Supports serial printing Yes
Shipped firmware Marlin

Files and slicing

Supported file formats G-code (.gcode, .gco, .g)

The printer

Printer manufacturer / brand AnkerMake
Printer model name M5C
Made by a company from China

Disclaimer: We strive to keep this information as current and accurate as possible, but cannot guarantee its completeness or reliability. Our data is based on user submissions and manufacturer references.

What filament can the AnkerMake M5C print?

Filament compatibility for the AnkerMake M5C: the materials it can handle, judged from its hotend, bed, chamber and enclosure.

Filament Suitability Notes
PLA Great The easiest filament to print. Works on almost any printer; a heated bed helps adhesion but is not required.
PETG Great Comfortably in range (PETG likes a ~230-250C hotend and a ~70-85C bed).
TPU & flexibles Great The direct-drive extruder feeds flexible filament well. Print slowly for clean results.
ABS & ASA With care The bed is hot enough, but ABS and ASA warp without an enclosure, which is strongly recommended for clean prints.
Nylon (PA) With care Possible with care - an enclosure and very dry filament are essential.
Polycarbonate (PC) With care On the edge - PC really wants an enclosed, hot chamber to avoid warping.
Carbon-fiber & glass-filled With care Possible if you fit a hardened or wear-resistant nozzle - the abrasive fibers quickly wear a stock brass nozzle.

Tip: this is a general guide from the printer's specs - always check your filament's recommended settings. With SimplyPrint you can save a profile for each spool and track exactly what filament you have in stock.

Printers like the AnkerMake M5C that work with SimplyPrint

Printers from the same maker, of a similar size, printing the same engineering materials or multi-material like it, that you can buy today and that we know work with SimplyPrint.

  • Bambu Lab P1S 3D printer
    Bambu Lab P1S
    256 x 256 x 256 mm
    Connects with: SimplyPrint Client
    Similar build volume
    Compatible
  • Creality Ender-3 3D printer
    Creality Ender-3
    220 x 220 x 250 mm
    Connects with: Klipper (Moonraker), OctoPrint
    Similar build volume
    Compatible
  • Bambu Lab A1 3D printer
    Bambu Lab A1
    256 x 256 x 256 mm
    Connects with: SimplyPrint Client
    Similar build volume
    Compatible
  • Creality Ender-3 v2 3D printer
    Creality Ender-3 v2
    220 x 220 x 250 mm
    Connects with: Klipper (Moonraker), OctoPrint
    Similar build volume
    Compatible
Compare 3D printers that work with SimplyPrint All AnkerMake printers

Frequently asked questions

Is the AnkerMake M5C compatible with SimplyPrint?

To our knowledge the AnkerMake M5C is not yet supported. SimplyPrint works with 130+ brands and 600+ models via OctoPrint, Klipper and built-in integrations - check the compatibility list for a supported printer.

What slicer should I use for the AnkerMake M5C?

We recommend PrusaSlicer for the AnkerMake M5C. You can run it, and 6 other slicers, directly in SimplyPrint's online slicer - no install, on any device, with profiles for the AnkerMake M5C kept up to date automatically.

Can I use OrcaSlicer with the AnkerMake M5C?

Yes. OrcaSlicer comes with a profile for the AnkerMake M5C, and you can run it in SimplyPrint's online slicer, so there's nothing to install.

What filament can the AnkerMake M5C print?

Based on its specs (hotend up to 300C, heated bed up to 100C), the AnkerMake M5C handles PLA, PETG, or TPU & flexibles well. See the full filament guide above for ABS, nylon, PC and composites.

What is the AnkerMake M5C's bed size and build volume?

The AnkerMake M5C has a 220 x 220 mm print bed and prints up to 250 mm tall, a build volume of about 220 x 220 x 250 mm. See the full specifications table above for bed type, temperatures and more.

© 2026 SimplyPrint. All rights reserved. This page and the compatibility, specification and review data on it are compiled by SimplyPrint and may not be copied, scraped, reproduced or republished, in whole or in part, without prior written permission. Printer images are the property of their respective manufacturers and are shown for identification purposes only; SimplyPrint claims no ownership of them. Quoted reviews belong to their authors.