China
Flashforge Finder at a glance
The Flashforge Finder is a 3D printer by Flashforge with a 140 x 140 x 140 mm build volume.
- Build volume
- 140 x 140 x 140 mm
- Prints well
- PLA, TPU & flexibles
Connect the Flashforge Finder to SimplyPrint
Does the Flashforge Finder 3D printer work with SimplyPrint, OctoPrint, Mainsail and Fluidd? Each way of connecting it, what it needs, and how to set it up.
-
SimplyPrint
Not compatible
-
Klipper (Moonraker)
Not compatible
-
OctoPrint
Directly, over USB
Not compatible
No known way to connect it to SimplyPrint
Unfortunately, the Flashforge Finder is currently not, to our knowledge, compatible with OctoPrint, Mainsail, Fluidd, or SimplyPrint. For the best 3D printing experience, consider other 3D printers that are compatible with these softwares.
How we determine compatibility
We consider a printer compatible if it works with one or more of the following:
- SimplyPrint custom integration for this specific model
- OctoPrint support (requires the printer to support serial printing)
- Klipper support (printer can run Klipper, either by flashing compatible firmware or using an external controller/pad)
OctoPrint compatibility is primarily based on whether the printer supports serial communication. If serial printing is not supported, we mark OctoPrint as not compatible.
Note: Some printers have third-party OctoPrint plugins that enable unofficial/custom connections. We don’t maintain a list of these plugins, so they are not reflected in our compatibility data.
What slicer to use for the Flashforge Finder
Use Kiri:Moto: it has a ready-made profile for the Flashforge Finder.
Ready-made profile for the Flashforge Finder
-
Kiri:MotoRuns in the SimplyPrint cloud
Flashforge's own slicer
-
Flash Studio / Orca-FlashforgeMade by Flashforge, not in the SimplyPrint cloud · Based on OrcaSlicer
-
FlashPrintMade by Flashforge, not in the SimplyPrint cloud
No profile for the Flashforge Finder
PrusaSlicer
OrcaSlicer
BambuStudio
ElegooSlicer
CrealityPrint
CuraWe only list slicers you can use in the SimplyPrint cloud, so there may be others for the Flashforge Finder.
Cloud-Based Slicer for Flashforge Finder: Use Kiri:Moto Online
Use Kiri:Moto and other slicers - directly in your browser with SimplyPrint's online cloud slicer. No installation required. Slice your Flashforge Finder models from any device, anywhere in the world!
Try Online Slicer NowProfiles and other slicers
Automatic Profile Updates: Profiles are automatically checked and fetched from the slicer GitHub repositories every day, as well as from our own open-source community-driven slicer profile database. This ensures you always have access to the latest profiles.
Note: Other slicers, such as Simplify3D, ideaMaker, SuperSlicer and KISSlicer, aren't in our cloud, so we don't track their profiles. They may still work well with your Flashforge Finder: check the slicer's own documentation or forums for a profile. You can also contribute profiles to our open-source slicer profile database on GitHub.
Flashforge Finder specifications: bed size, print height and more
Its size, temperatures, multi-material and how it connects, from the maker and our own research.
Size
| Build volume | 140 x 140 x 140 mm |
|---|---|
| Bed type | Square |
| Bed size | 140 x 140 mm |
| Max print height | 140 mm |
Printing
| Max extruder temperature | 240 °C |
|---|---|
| Has heated bed | No |
| Number of nozzles | 1 |
| Direct drive | Yes |
| Probing tool / Auto Bed Leveling | No |
| Filament width | 1.75 mm |
Connecting
| Supports serial printing | Yes |
|---|---|
| Shipped firmware | Marlin |
Files and slicing
| Supported file formats | G-code (.gcode, .gco, .g) |
|---|
The printer
| Printer manufacturer / brand | Flashforge |
|---|---|
| Printer model name | Finder |
| Made by a company from | China |
Disclaimer: We strive to keep this information as current and accurate as possible, but cannot guarantee its completeness or reliability. Our data is based on user submissions and manufacturer references.
What filament can the Flashforge Finder print?
Filament compatibility for the Flashforge Finder: the materials it can handle, judged from its hotend, bed, chamber and enclosure.
| Filament | Suitability | Notes |
|---|---|---|
| PLA | Great | The easiest filament to print. Works on almost any printer; a heated bed helps adhesion but is not required. |
| PETG | With care | Marginal - PETG prefers a hotter bed (~70-80C) than this printer reaches. |
| TPU & flexibles | Great | The direct-drive extruder feeds flexible filament well. Print slowly for clean results. |
| ABS & ASA | Not ideal | Not recommended - the bed cannot reach the ~90-110C ABS and ASA need. |
| Nylon (PA) | Not ideal | Not recommended - nylon needs a hotter hotend (~250-270C) and ideally an enclosure. |
| Polycarbonate (PC) | Not ideal | Not recommended - PC needs very high hotend temps and an enclosed chamber. |
| Carbon-fiber & glass-filled | With care | Possible if you fit a hardened or wear-resistant nozzle - the abrasive fibers quickly wear a stock brass nozzle. |
Tip: this is a general guide from the printer's specs - always check your filament's recommended settings. With SimplyPrint you can save a profile for each spool and track exactly what filament you have in stock.
Printers like the Flashforge Finder that work with SimplyPrint
Printers from the same maker, of a similar size, printing the same engineering materials or multi-material like it, that you can buy today and that we know work with SimplyPrint.
-
Flashforge Finder 2
140 x 140 x 140 mmConnects with: OctoPrintAlso by Flashforge · Similar build volumeCompatible -
Flashforge Inventor II S
140 x 140 x 150 mmConnects with: OctoPrintAlso by Flashforge · Similar build volumeCompatible -
XYZprinting da Vinci mini w+
150 x 150 x 150 mmConnects with: Klipper (Moonraker), OctoPrintSimilar build volumeCompatible -
LulzBot Mini
152 x 152 x 158 mmConnects with: Klipper (Moonraker), OctoPrintSimilar build volumeCompatible
Frequently asked questions
Is the Flashforge Finder compatible with SimplyPrint?
To our knowledge the Flashforge Finder is not yet supported. SimplyPrint works with 130+ brands and 600+ models via OctoPrint, Klipper and built-in integrations - check the compatibility list for a supported printer.
What slicer should I use for the Flashforge Finder?
We recommend Kiri:Moto for the Flashforge Finder. You can run it, and 6 other slicers, directly in SimplyPrint's online slicer - no install, on any device, with profiles for the Flashforge Finder kept up to date automatically.
Can I use OrcaSlicer with the Flashforge Finder?
Yes, but OrcaSlicer has no built-in profile for the Flashforge Finder that we know of: start from a similar printer's profile and set the bed size, height and nozzle to match.
What filament can the Flashforge Finder print?
Based on its specs (hotend up to 240C, no heated bed), the Flashforge Finder handles PLA or TPU & flexibles well. See the full filament guide above for ABS, nylon, PC and composites.
What is the Flashforge Finder's bed size and build volume?
The Flashforge Finder has a 140 x 140 mm print bed and prints up to 140 mm tall, a build volume of about 140 x 140 x 140 mm. See the full specifications table above for bed type, temperatures and more.
© 2026 SimplyPrint. All rights reserved. This page and the compatibility, specification and review data on it are compiled by SimplyPrint and may not be copied, scraped, reproduced or republished, in whole or in part, without prior written permission. Printer images are the property of their respective manufacturers and are shown for identification purposes only; SimplyPrint claims no ownership of them. Quoted reviews belong to their authors.