Skip to main content

Raise3D E2: specs, SimplyPrint compatibility and setup

By Raise3D, China

Raise3D E2 image

Does it work with SimplyPrint?

Not compatible We're sure

To our knowledge it can't connect to SimplyPrint, not even through OctoPrint or Klipper.

See printers that work

Raise3D E2 at a glance

The Raise3D E2 is a 3D printer by Raise3D with a 330 x 240 x 240 mm build volume.

Build volume
330 x 240 x 240 mm
Prints well
PLA, PETG
All specifications

Connect the Raise3D E2 to SimplyPrint

Does the Raise3D E2 3D printer work with SimplyPrint, OctoPrint, Mainsail and Fluidd? Each way of connecting it, what it needs, and how to set it up.

  • SimplyPrint

    SimplyPrint

    Not compatible

  • Mainsail Fluidd

    Klipper (Moonraker)

    Not compatible

  • OctoPrint

    OctoPrint

    Directly, over USB

    Not compatible

No known way to connect it to SimplyPrint

Unfortunately, the Raise3D E2 is currently not, to our knowledge, compatible with OctoPrint, Mainsail, Fluidd, or SimplyPrint. For the best 3D printing experience, consider other 3D printers that are compatible with these softwares.

How we determine compatibility

We consider a printer compatible if it works with one or more of the following:

  • SimplyPrint custom integration for this specific model
  • OctoPrint support (requires the printer to support serial printing)
  • Klipper support (printer can run Klipper, either by flashing compatible firmware or using an external controller/pad)

OctoPrint compatibility is primarily based on whether the printer supports serial communication. If serial printing is not supported, we mark OctoPrint as not compatible.

Note: Some printers have third-party OctoPrint plugins that enable unofficial/custom connections. We don’t maintain a list of these plugins, so they are not reflected in our compatibility data.

See printers that work View Compatible Printers

What slicer to use for the Raise3D E2

None of the slicers in SimplyPrint's cloud has a ready-made profile for the Raise3D E2, but it takes standard G-code: start from a similar printer's profile and set the bed size, height and nozzle to match.

Raise3D's own slicer

  • ideaMaker
    Made by Raise3D, not in the SimplyPrint cloud

No profile for the Raise3D E2

We only list slicers you can use in the SimplyPrint cloud, so there may be others for the Raise3D E2.

Cloud-Based Slicer for Raise3D E2

All supported slicers - directly in your browser with SimplyPrint's online cloud slicer. No installation required. Slice your Raise3D E2 models from any device, anywhere in the world!

Try Online Slicer Now
Profiles and other slicers

Automatic Profile Updates: Profiles are automatically checked and fetched from the slicer GitHub repositories every day, as well as from our own open-source community-driven slicer profile database. This ensures you always have access to the latest profiles.

Note: Other slicers, such as Simplify3D, ideaMaker, SuperSlicer and KISSlicer, aren't in our cloud, so we don't track their profiles. They may still work well with your Raise3D E2: check the slicer's own documentation or forums for a profile. You can also contribute profiles to our open-source slicer profile database on GitHub.

Raise3D E2 specifications: bed size, print height and more

Its size, temperatures, multi-material and how it connects, from the maker and our own research.

Size

Build volume 330 x 240 x 240 mm
Bed type Rectangle
Bed size 330 x 240 mm
Max print height 240 mm

Printing

Max extruder temperature 300 °C
Has heated bed Yes
Max bed temperature 110 °C
Number of nozzles 1
Direct drive No
Probing tool / Auto Bed Leveling Yes
Filament width 1.75 mm

Connecting

Supports serial printing Yes
Shipped firmware Marlin

Files and slicing

Supported file formats G-code (.gcode, .gco, .g)

The printer

Printer manufacturer / brand Raise3D
Printer model name E2
Made by a company from China

Disclaimer: We strive to keep this information as current and accurate as possible, but cannot guarantee its completeness or reliability. Our data is based on user submissions and manufacturer references.

What filament can the Raise3D E2 print?

Filament compatibility for the Raise3D E2: the materials it can handle, judged from its hotend, bed, chamber and enclosure.

Filament Suitability Notes
PLA Great The easiest filament to print. Works on almost any printer; a heated bed helps adhesion but is not required.
PETG Great Comfortably in range (PETG likes a ~230-250C hotend and a ~70-85C bed).
TPU & flexibles With care Possible, but a Bowden extruder makes flexibles harder - print slowly and prefer firmer (higher-shore) TPU.
ABS & ASA With care The bed is hot enough, but ABS and ASA warp without an enclosure, which is strongly recommended for clean prints.
Nylon (PA) With care Possible with care - an enclosure and very dry filament are essential.
Polycarbonate (PC) With care On the edge - PC really wants an enclosed, hot chamber to avoid warping.
Carbon-fiber & glass-filled With care Possible if you fit a hardened or wear-resistant nozzle - the abrasive fibers quickly wear a stock brass nozzle.

Tip: this is a general guide from the printer's specs - always check your filament's recommended settings. With SimplyPrint you can save a profile for each spool and track exactly what filament you have in stock.

Printers like the Raise3D E2 that work with SimplyPrint

Printers from the same maker, of a similar size, printing the same engineering materials or multi-material like it, that you can buy today and that we know work with SimplyPrint.

  • Raise3D Pro2 3D printer
    Raise3D Pro2
    305 x 305 x 300 mm
    Connects with: Klipper (Moonraker), OctoPrint
    Also by Raise3D · Similar build volume
    Compatible
  • Bambu Lab P1S 3D printer
    Bambu Lab P1S
    256 x 256 x 256 mm
    Connects with: SimplyPrint Client
    Similar build volume
    Compatible
  • Bambu Lab A1 3D printer
    Bambu Lab A1
    256 x 256 x 256 mm
    Connects with: SimplyPrint Client
    Similar build volume
    Compatible
  • Bambu Lab X1-Carbon Combo 3D printer
    Bambu Lab X1-Carbon Combo
    256 x 256 x 256 mm
    Connects with: SimplyPrint Client
    Similar build volume
    Compatible
Compare 3D printers that work with SimplyPrint All Raise3D printers

Frequently asked questions

Is the Raise3D E2 compatible with SimplyPrint?

To our knowledge the Raise3D E2 is not yet supported. SimplyPrint works with 130+ brands and 600+ models via OctoPrint, Klipper and built-in integrations - check the compatibility list for a supported printer.

What slicer should I use for the Raise3D E2?

Cura, PrusaSlicer and OrcaSlicer all work with the Raise3D E2, and you can run any of them in SimplyPrint's online browser slicer - no install needed, on any device.

Can I use OrcaSlicer with the Raise3D E2?

Yes, but OrcaSlicer has no built-in profile for the Raise3D E2 that we know of: start from a similar printer's profile and set the bed size, height and nozzle to match.

What filament can the Raise3D E2 print?

Based on its specs (hotend up to 300C, heated bed up to 110C), the Raise3D E2 handles PLA or PETG well. See the full filament guide above for ABS, nylon, PC and composites.

What is the Raise3D E2's bed size and build volume?

The Raise3D E2 has a 330 x 240 mm print bed and prints up to 240 mm tall, a build volume of about 330 x 240 x 240 mm. See the full specifications table above for bed type, temperatures and more.

© 2026 SimplyPrint. All rights reserved. This page and the compatibility, specification and review data on it are compiled by SimplyPrint and may not be copied, scraped, reproduced or republished, in whole or in part, without prior written permission. Printer images are the property of their respective manufacturers and are shown for identification purposes only; SimplyPrint claims no ownership of them. Quoted reviews belong to their authors.