China
Snapmaker Artisan at a glance
The Snapmaker Artisan is a 3D printer by Snapmaker with a 400 x 400 x 400 mm build volume.
- Build volume
- 400 x 400 x 400 mm
- Prints well
- PLA, PETG, TPU & flexibles
Connect the Snapmaker Artisan to SimplyPrint
Does the Snapmaker Artisan 3D printer work with SimplyPrint, OctoPrint, Mainsail and Fluidd? Each way of connecting it, what it needs, and how to set it up.
-
SimplyPrint
Not compatible
-
Klipper (Moonraker)
Not compatible
-
OctoPrint
Directly, over USB
Not compatible
No known way to connect it to SimplyPrint
Unfortunately, the Snapmaker Artisan is currently not, to our knowledge, compatible with OctoPrint, Mainsail, Fluidd, or SimplyPrint. For the best 3D printing experience, consider other 3D printers that are compatible with these softwares.
How we determine compatibility
We consider a printer compatible if it works with one or more of the following:
- SimplyPrint custom integration for this specific model
- OctoPrint support (requires the printer to support serial printing)
- Klipper support (printer can run Klipper, either by flashing compatible firmware or using an external controller/pad)
OctoPrint compatibility is primarily based on whether the printer supports serial communication. If serial printing is not supported, we mark OctoPrint as not compatible.
Note: Some printers have third-party OctoPrint plugins that enable unofficial/custom connections. We don’t maintain a list of these plugins, so they are not reflected in our compatibility data.
What slicer to use for the Snapmaker Artisan
Use PrusaSlicer, OrcaSlicer, ElegooSlicer, or CrealityPrint: each has a ready-made profile for the Snapmaker Artisan.
Ready-made profile for the Snapmaker Artisan
-
PrusaSlicerRuns in the SimplyPrint cloud -
OrcaSlicerRuns in the SimplyPrint cloud -
ElegooSlicerRuns in the SimplyPrint cloud -
CrealityPrintRuns in the SimplyPrint cloud
Snapmaker's own slicer
-
Snapmaker OrcaMade by Snapmaker, not in the SimplyPrint cloud · Based on OrcaSlicer
-
Snapmaker LubanMade by Snapmaker, not in the SimplyPrint cloud
No profile for the Snapmaker Artisan
BambuStudio
Cura
Kiri:MotoWe only list slicers you can use in the SimplyPrint cloud, so there may be others for the Snapmaker Artisan.
Cloud-Based Slicer for Snapmaker Artisan: Use PrusaSlicer Online
Use PrusaSlicer and other slicers - directly in your browser with SimplyPrint's online cloud slicer. No installation required. Slice your Snapmaker Artisan models from any device, anywhere in the world!
Try Online Slicer NowProfiles and other slicers
Automatic Profile Updates: Profiles are automatically checked and fetched from the slicer GitHub repositories every day, as well as from our own open-source community-driven slicer profile database. This ensures you always have access to the latest profiles.
Note: Other slicers, such as Simplify3D, ideaMaker, SuperSlicer and KISSlicer, aren't in our cloud, so we don't track their profiles. They may still work well with your Snapmaker Artisan: check the slicer's own documentation or forums for a profile. You can also contribute profiles to our open-source slicer profile database on GitHub.
Snapmaker Artisan specifications: bed size, print height and more
Its size, temperatures, multi-material and how it connects, from the maker and our own research.
Size
| Build volume | 400 x 400 x 400 mm |
|---|---|
| Bed type | Square |
| Bed size | 400 x 400 mm |
| Max print height | 400 mm |
Printing
| Max extruder temperature | 300 °C |
|---|---|
| Has heated bed | Yes |
| Max bed temperature | 110 °C |
| Number of nozzles | 1 |
| Direct drive | Yes |
| Probing tool / Auto Bed Leveling | Yes |
| Filament width | 1.75 mm |
Connecting
| Supports serial printing | Yes |
|---|---|
| Shipped firmware | Marlin |
Files and slicing
| Supported file formats | G-code (.gcode, .gco, .g) |
|---|
The printer
| Printer manufacturer / brand | Snapmaker |
|---|---|
| Printer model name | Artisan |
| Made by a company from | China |
Disclaimer: We strive to keep this information as current and accurate as possible, but cannot guarantee its completeness or reliability. Our data is based on user submissions and manufacturer references.
What filament can the Snapmaker Artisan print?
Filament compatibility for the Snapmaker Artisan: the materials it can handle, judged from its hotend, bed, chamber and enclosure.
| Filament | Suitability | Notes |
|---|---|---|
| PLA | Great | The easiest filament to print. Works on almost any printer; a heated bed helps adhesion but is not required. |
| PETG | Great | Comfortably in range (PETG likes a ~230-250C hotend and a ~70-85C bed). |
| TPU & flexibles | Great | The direct-drive extruder feeds flexible filament well. Print slowly for clean results. |
| ABS & ASA | With care | The bed is hot enough, but ABS and ASA warp without an enclosure, which is strongly recommended for clean prints. |
| Nylon (PA) | With care | Possible with care - an enclosure and very dry filament are essential. |
| Polycarbonate (PC) | With care | On the edge - PC really wants an enclosed, hot chamber to avoid warping. |
| Carbon-fiber & glass-filled | With care | Possible if you fit a hardened or wear-resistant nozzle - the abrasive fibers quickly wear a stock brass nozzle. |
Tip: this is a general guide from the printer's specs - always check your filament's recommended settings. With SimplyPrint you can save a profile for each spool and track exactly what filament you have in stock.
Printers like the Snapmaker Artisan that work with SimplyPrint
Printers from the same maker, of a similar size, printing the same engineering materials or multi-material like it, that you can buy today and that we know work with SimplyPrint.
-
Snapmaker U1
270 x 270 x 270 mmConnects with: SimplyPrint Client, Klipper (Moonraker)Also by SnapmakerCompatible -
Creality Ender-5 Plus
350 x 350 x 400 mmConnects with: Klipper (Moonraker), OctoPrintSimilar build volumeCompatible -
Creality K2 Plus Combo
350 x 350 x 350 mmConnects with: SimplyPrint Client, Klipper (Moonraker)Similar build volumeCompatible -
ELEGOO Neptune 4 Max
420 x 420 x 480 mmConnects with: Klipper (Moonraker)Similar build volumeCompatible
Frequently asked questions
Is the Snapmaker Artisan compatible with SimplyPrint?
To our knowledge the Snapmaker Artisan is not yet supported. SimplyPrint works with 130+ brands and 600+ models via OctoPrint, Klipper and built-in integrations - check the compatibility list for a supported printer.
What slicer should I use for the Snapmaker Artisan?
We recommend PrusaSlicer for the Snapmaker Artisan. You can run it, and 6 other slicers, directly in SimplyPrint's online slicer - no install, on any device, with profiles for the Snapmaker Artisan kept up to date automatically.
Can I use OrcaSlicer with the Snapmaker Artisan?
Yes. OrcaSlicer comes with a profile for the Snapmaker Artisan, and you can run it in SimplyPrint's online slicer, so there's nothing to install.
What filament can the Snapmaker Artisan print?
Based on its specs (hotend up to 300C, heated bed up to 110C), the Snapmaker Artisan handles PLA, PETG, or TPU & flexibles well. See the full filament guide above for ABS, nylon, PC and composites.
What is the Snapmaker Artisan's bed size and build volume?
The Snapmaker Artisan has a 400 x 400 mm print bed and prints up to 400 mm tall, a build volume of about 400 x 400 x 400 mm. See the full specifications table above for bed type, temperatures and more.
© 2026 SimplyPrint. All rights reserved. This page and the compatibility, specification and review data on it are compiled by SimplyPrint and may not be copied, scraped, reproduced or republished, in whole or in part, without prior written permission. Printer images are the property of their respective manufacturers and are shown for identification purposes only; SimplyPrint claims no ownership of them. Quoted reviews belong to their authors.